Tribological mechanism of micro-arc oxidation coatings prepared by different electrolyte systems in artificial seawater

The micro-arc oxidation (MAO) coatings were prepared in four different electrolyte systems, including mixed acid, phosphate, phosphate-aluminate and phosphate-silicate electrolytes. The friction and wear properties of MAO coatings in ambient air, seawater and four groups of saline solutions related to seawater were investigated. The results showed that the addition of silicate to phosphate could increase the density of the coating. The phosphate-aluminate ceramic layer exhibited the lowest wear rate in various environments. Additionally, the friction coefficient and wear rate of MAO coating in seawater were lower than those in ambient air, which was due to the boundary lubrication effect of seawater. Meanwhile, the presence of divalent metal salts in seawater made its lubricity better than other salt solutions.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Effect of malondialdehyde oxidation on structure and physicochemical properties of amandin

Oil, accounting for 45% of almonds, is easily oxidised and can further induce the protein oxidation to reduce their quality. Structure and physicochemical properties of amandin, the main water-soluble protein in almonds, inducing oxidation by malondialdehyde (MDA) were investigated. The results showed that the content of carbonyl group increased from 5.23 to 33.25 nmol mg⁻¹ of protein with the increase in MDA concentration (P < 0.05). However, the sulphydryl content, surface hydrophobicity, particle size and the absolute value of ζ-potential first increased and then decreased. Fourier-transformed infrared spectroscopy (FT-IR) confirmed that the structure of amandin changed from order to disorder. Fluorescence spectroscopic analysis revealed that mild oxidation (0–0.1 mmol L⁻¹ MDA) exposed hydrophobic groups of the protein. Sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) suggested that protein oxidation promoted crosslinking between protein molecules. Furthermore, protein oxidation markedly declined the total amino acid content of amandin (P < 0.05). In conclusion, MDA oxidation changed the structure and amino acid content of amandin, and caused the protein aggregate and crosslink through hydrophobic interaction and electrostatic interaction.     

Structural characteristics and high-temperature oxidation behaviour of nano-HfO2-doped thermal barrier coatings

The uneven growth of thermally grown oxides (TGOs) in thermal barrier coating systems is an important cause of cracking failure at the coating interface in high-temperature environments. The doping of rare earth elements in the bonding layer can effectively inhibit the formation of spinel oxides in the TGO and improve the high-temperature oxidation resistance of the coating. However, a single rare earth element has a limited effect on inhibiting TGO failure. In this study, a NiCoCrAlYHf coating was prepared using a supersonic flame spraying (HVOF) technique. The effects of HfO₂ doping on the high-temperature oxidation behaviour of the coatings and diffusion behaviour of metallic elements in the coatings were investigated at 1100 °C. The results showed that the nano-sized HfO₂ filled the pores between the powder particles and improved the hardness of the coating. During the high-temperature oxidation process, the oxides formed by Hf and Y had a large size and low solubility, which effectively blocked the diffusion of Al. This slowed the generation of spinel oxides, effectively inhibited the growth of the TGO, it inhibits the initiation and propagation of cracks within the coating, reduces damage to the coating from tensile and compressive stresses at the interface, and improved the high-temperature oxidation resistance of the coating.     

Catalytic supercritical water oxidation of tri-n-butyl phosphate: Process optimization by response surface methodology and cytotoxicity assessment

Catalytic supercritical water oxidation (SCWO) of an organophosphate flame retardant, namely tri-n-butyl phosphate (TNBP) was studied. Firstly, copper oxide nanoparticles (NPs) were synthesized in SCW and their properties were characterized by various analyses. Afterwards, their catalytic performance was investigated under different conditions including reaction temperature (400–500 °C), TNBP volume percentage in the feed (1–4%), oxidant ratio (0–2) and reaction time (50–150 min) based on response surface methodology (RSM). The synthesized CuO NPs had an average particle size of 30 nm with a narrow distribution. According to RSM analysis, the reaction temperature and time are the most significant factors; whereas, the impact of the other factors, especially TNBP volume percentage in the feed, was found to be negligible. Overall, excellent performance was achieved under optimal conditions found by the RSM, which was reaction temperature of 500 °C, TNBP volume percentage of 4%, oxidant ratio of 1.5, and reaction time of 90 min. The TOC removal efficiency as an indicator of TNBP degradation was about 99%. Finally, in vitro cell viability assays for the cytotoxicity evaluation of fresh and SCW-treated solution were applied. The results of MTT showed that SCWO converts TNBP into by-product that did not induce any cytotoxicity.     

The toughening design of multi-layer antioxidation coating on C/C matrix via SiC-SiCw transition layer grown in-situ

Poor antioxidant and thermal-shock capacities of C/C composites thermal barrier coating (TBC) caused by cracking and shedding of coatings has been a major obstacle blocking the development of C/C composites. Herein, in-situ growth of whisker reinforced silicon carbide transition layer and inter-embedding mechanism of multi-gradient coatings were brought into the design of TBC to enhance the antioxidant and thermal-shock capacities. A three-layer gradient coating SiC-SiC_w/ZrB₂-SiC/ZrSiO₄-aluminosilicate glass (ZAG) from inside to outside, in which ZrB₂-SiC/ZAG serve as oxygen barrier layers with self-healing ability and SiC-SiC_w provides thermal stress buffering and bonding against cracking and shedding of coatings, is designed. The ZAG mainly forms a dense oxygen blocking frontier with self-healing ability through fluidized glass, while the ZrB₂-SiC can react actively with infiltrated oxygen in a way of self-sacrifice, preventing oxygen erosion to C/C matrix and SiC-SiC_w transition layer. As a result, the collaborative work among layers endows this coating with excellent high temperature service performance. This work provides a new insight for the design of excellent TBC.     

Systematic optimization of corrosion,bioactivity, and biocompatibility behaviors of calcium-phosphate plasma electrolytic oxidation (PEO) coatings on titanium substrates

To optimize the corrosion, bioactivity, and biocompatibility behaviors of plasma electrolytic oxidation (PEO) coatings on titanium substrates, the effects of five process variables including frequency, current density, duty cycle, treatment time, and electrolyte Ca/P ratio were evaluated. In our systematic study, a Taguchi design of experimental based on an L16 orthogonal array was used. For this, the coatings characteristics such as the surface roughness, wettability, rutile to anatase and Ca/P ratios, and corrosion polarization resistance were investigated. After determining the optimum process variables for each response, the apatite forming ability in SBF (bioactivity behavior) and MG63 cell attachment and flattening (biocompatibility behavior) for two groups of coatings were examined. The first group was optimized based on the maximum corrosion polarization resistance and the variables were set as the frequency of 2000 Hz, the current density of 5 A/dm², the duty cycle of 30%, the treatment time of 5 min, and the Ca/P ratio of 0.65 at. % in the electrolyte. For the second group, the maximum surface roughness, greatest Ca/P ratio, and highest wettability as well as the minimum rutile to anatase ratio in coatings, could be obtained when the variables were set as the frequency of 10 Hz, the current density of 12.5 A/dm², the duty cycle of 50%, the treatment time of 12.5 min, and the Ca/P ratio of 1.70 at. % in the electrolyte. The results showed that while both groups of coatings indicated a significant apatite forming ability and can serve as bioactive coatings, a proper attachment and flattening of cells and consequently, the favorable biocompatibility properties were seen only in the first group.     

炼油厂碱渣酚分析及钛硅分子筛对双氧水氧化苯酚的催化作用

对炼油厂碱渣中酚含量和组成进行了分析，结果表明，碱渣酚含量较高，且含多种不同结构的酚，其中苯酚含量相对最高，达到60%左右。采用双氧水氧化苯酚的试验结果表明：双氧水氧化效果较差，苯酚去除率仅为0.5%；使用钛硅分子筛作催化剂，可大幅提高双氧水氧化苯酚的效果，最佳氧化条件下苯酚去除率高达94.7%，显示出钛硅分子筛优异的催化氧化作用。     

Efficient hydrogen production for industry and electricity storage via high-temperature electrolysis

The paper describes the development status of Sunfire's reversible solid oxide cell (RSOC) technology. Here, Sunfire is a pioneer in the field of high-temperature electrolysers (HTE) for renewable hydrogen production which can be operated as a fuel cell for power generation in a reverse mode. The maturity of the technology is improved stepwise so that first applications in the field of hydrogen production for industry and electricity storage can be tackled. Three application examples where larger scale prototype has been installed will be discussed: 1) A power-to-power electricity storage based on hydrogen, 2) a RSOC unit that is installed in an iron and steel works, and 3) a pressurized SOEC prototype which will be integrated with a methanation unit. Results show the potentials of the technology in connection with fluctuating renewable energy sources.     

Effect of preparation method on physicochemical properties and catalytic performances of LaCoO_3 perovskite for CO oxidation

Perovskite oxides LaCoO_3 prepared by templating, co-precipitation and sol-gel method with different complexants were systematically characterized and its catalytic performances for CO oxidation were investigated. The samples were characterized by X-ray diffraction, thermogravimetry analysis and differential scanning calorimetry, N_2 physisorption, transmission electron microscopy, temperature program reduction of hydrogen, temperature program desorption of oxygen and X-ray photoelectron spectroscopy measurement, results of which show that the properties of LaCoO_3, such as surface morphology, surface area, surface compositions, redox capability, oxygen vacancy, as well as the calcination temperature and formation mechanism, depend intimately on the preparation method. Catalytic tests indicate that the sample prepared by carbon templating method shows the best activity for CO oxidation, with full CO conversion obtained at 135 ℃. In particular, the catalyst can be activated and significant increase of activity can be obtained with the increase of reaction time. The cyclic and longterm stability of catalysts were discussed and compared.